Friday, October 10, 2008

Solar Lamppost

Solar Lamppost,Solar Street Light Pole
Solar Street Light Pole, Solar Street Lamppost CAD drawing.
Tubular
Height:3500mm
Edit by Ben
rammbodeng@gmail.com
Solar Lamppost Posted by Picasa

Monday, September 29, 2008

Singapore night race will not be dark…

  
Singapore F1 track 


Here’s a new picture showing just how bright the lighting will be at the inaugual Singapore Grand Prix this year:

Singapore night lighting 2, 470313

The Singapore race organisers trialled a new lighting system recently along St Andrew’s Road in front of the Padang - where the cars will hit 260kph during this year’s race.

More pictures below:

Singapore night lighting 1, 470313

Singapore night lighting 3, 470313

They’ve also tested out the lighting system that will be used for flag warnings:

Singapore night lighting 4, 470313

Concerns have been expressed by drivers and fans about the safety of racing at night - but from these pictures it looks as though the race will be very well-lit.

According to the organisers the pit building is 65% complete and resurfacing work on parts of the circuit are and resurfacing work on part of the track has begun.

The 2008 Singapore Grand Prix will be held on 26-28th September. It will be F1’s first night race and is expected to be followed by Malaysia in 2009 and possibly several other Asian circuits in the near future.


Wednesday, September 24, 2008

Low Voltage Bollard Light

Low Voltage Bollard Ligh
Bollard Light - Black
Premium cast metal construction
Textured Black Finish
Clear glass lens
Halogen Bulbs
Email us: info@shuguanglamps.com
Low Voltage Bollard Light

Monday, September 22, 2008

How to select Street Light Poles ?


How to select Poles ? 
Street Light Pole,Lamp post
Poles should initially be selected, according to lighting application needs and second, but equally important, according to the structural requirements imposed on the pole by the required lighting fixtures and bracketry. Before attempting to make this selection, it would be helpful to have an understanding of the terminology, such as steady wind velocity, gust velocity, EPA, special wind region and maximum weight. Then a step-by-step procedure can be followed to select the proper pole for your particular requirements.

Steady Wind Velocity
This is the maximum steady wind velocity expressed in MPH likely to occur in a specific location. Refer to Iso-Tach wind map on the next page for the wind velocity in your location.

Gust Velocity
Gust velocity is a momentary increase in wind causing a whipping action. In all cases, Hubbell pole calculations include a 1.3 gust factor over steady wind velocity. This means that poles designed to withstand winds of 80 MPH will withstand gusts to 104 MPH.

Effective Projected Area
Effective Projected Area (EPA) is the exposed surface area of a fixture or bracket multiplied by a shape factor which varies depending on the shape of the fixture or bracket. For example, a large rectangular fixture will present more resistance to the wind than will a round or cylindrical shape.

Special Wind Regions
Some locations such as mountainous areas and areassurrounding the Great Lakes exhibit wind velocitiesconsiderably higher than the surrounding areas. Consult local authorities to determine maximum wind velocities and select equipment accordingly.

Maximum Weight
This is the maximum allowable total weight the pole is capable of supporting. Its value is determined by the total weight of the lighting fixtures and bracketry for your application requirements.

Pole Selection Procedure
With an understanding of the parameters for poleselection, you can follow this simple step-by-stepprocedure and, with confidence, select a pole to meet your particular requirements.
1. Determine the site location and steady wind velocity by referring to the Iso-Tach map. If the location falls between Iso-Tach bars or on the 70 or 90 MPH bar, use the next highest wind velocity; i.e., 80 or 100 MPH. If the steady wind exceeds 100 MPH, consult factory.
2. Total the EPA for the required luminaires andbracketry.
3. Total the weight of the luminaires and bracketry.
4. Compare steps 2 and 3 with the maximum allowable EPA and weight as shown for the style, material and height pole required. The maximum allowable must be equal to or exceed the totals from steps 2 and 3.

Pole Selection Concerns
Reference the Pole Selection Guide and Installation & Maintenance Concerns on every pole catalog page.

Caution: These selection methods are guidelines only. Hubbell Lighting assumes no responsibility forselection and recommends you consult qualifiedprofessionals for verification of overall system design, site suitability, foundation considerations and applicable code and regulatory conformances.
Maintenance: The facility owner’s/manager’s regular scheduled maintenance program must include initial and regular follow-up inspections for structural damage, broken welds, tampering, nut loosening, missing wire covers, dangling electrical wiring, internal or external corrosion, foundation settlement, excessive shaft deflection and vibration for all lighting poles. Immediate repair or replacement may be necessary.

Overloading: Do not overload poles by attaching flags, banners or any items that can add excessive wind or mechanical load to designed pole assemblies.

Observation: Installation and local area conditions can dramatically affect lighting pole performance. Excessive vibration may result from some wind and mounting conditions. Only individuals with local knowledge, who have observed or inspected the site can effectively evaluate site specific issues. Consult the factory for information on vibration dampers, special corrosion, foundation settlement, excessive shaft deflection and vibration for all lighting poles. Immediate repair or replacement may be necessary.

Sunday, September 21, 2008

Lighting

Lighting has become increasingly important for commercial and retail property owners for increased sales, security and safety for tenants and customers. Pole lights are an integral part of these three issues. Site lighting provides necessary lumens to a parking lot or parking garage. Dealing with the ongoing maintenance of these light poles has always been an issue for property owners, property managers and maintenance personnel. Maintaining a brightly lit parking lot has always had it's challenges. The lighting design for new installations of parking lots have now been placed in the hands of photometric engineers. Photometrics optimizes the maximum amount of light to an area with the least amount of light heads and poles. There are many different types of light heads available in different voltages and lamp wattages to the end user. With all of these different selections there now is an option to add Retropole to your new or existing light pole to maximize the ability to replace a ballast or lamp as soon as the light burns out without the need to schedule an electrical contractor. Commercial and industrial lighting once installed is often overlooked until there is a problem with burned out lamps. Retropole offers immediate replacement of lamps or ballasts without the need of waiting for many lamps to go out before making a service call feasable. Lighting designers focus on making parking lots look attractive but often neglect ongoing lighting maintenance which ultimately is left to property owners to deal with. Retropole lighting products are the solution for this problem. Insist on Retropole for new or redevelopment projects for easier property maintenance after building contractors have left the job. It's sleek attractive look works with any lighting design whether it be contemporary lighting or traditional lighting and is color matched to any light head or light pole.
Outdoor Light Fixtures

Outdoor light fixtures for most parking lots are on a 25 to 30 foot light pole. These fixtures come in many shapes and sizes with a variety of voltages and lamp choices. Typically these pole lights are either high pressure sodium, metal halide or mercury vapor. Lamps go out usually in a year, however, hid lighting suffers from a reduction of lumens over time resulting in a loss of light output even though lamps are still burning.

You can identify which type of light you have in your parking lot by the color emitted by your lamp. Metal halide lamps cast a white light, high pressure sodium lamps emit a yellowish hue and mercury vapor lamps project a light blue color that works nicely as landscape lighting. These pole lights, as different as they seem, have one common flaw. They are inaccessible.

Saturday, September 20, 2008

Galvanised Taper Street Light Pole

Galvanised Taper Street Light Pole

Galvanised Taper Street Light Pole
Galvanised Taper Street Light Pole

Galvanised Taper Street Light Pole

Selling Lead
Galvanised steel poles (columns) + powder coating (white) Decorative bracket, Steel conical tapered columns
Base Plate , flange
preserving: hot dip galvanised+ powder coated (white)

Thursday, September 18, 2008

steel columns for public lighting

cilindrical-conical, seamless drawnWith our two advanced machineries, we are able to produce cilindrical-conical tapered lighting columns without the familiar visible welded seam running from top to bottom. These columns will be drawn from cylindrical tubes. For these columns, we can guarantee the exact diameter (?8 till ?73 mm), length (maximum 16 meter), wall thickness (3 till 6,3 mm) and conicity can be guaranteed. All conicities are possible. Under the chapter conical tubes and 'special tubes', you can find additional information about different shapes, such as parabola, cigar, ribbed or tubes with decorative elements.
While there are no visible welds, the columns will have a longer life time. The non-interupted structure and the rounding on the total length of the column will take care for a better stability of the column and luminiare.
cilindrical stepped (variable diameters)A classic column, which has been used for decades, is the cilindrical stepped column. This type of column can be delivered in different variants: post columns, columns with fixed or mountable brackets, foldable column, lighting columns with banners, etc. All types of columns can be supplied with wedges, ground plate or base plate.The cilindrical stepped columns can be produced out of one piece till a length of 22 meters. If you need lighting columns with a length of minimal 22 meter and it is necessery to hot dip galvanise the column, then we have to split up the column in two sections (due to the length of the zinc bath) We are happy to inform you about the correct solutions.


lighting columns



lighting columns
steel conical tapered columns, seamless drawn, supplied with a double bracket for public lighting. The bracket is produced from two conical tapered tubes, seamless drawn. Preserving: hot dip galvanised according to EN ISO 1461 and powder coated.





lighting columns
lighting column
steel cilindrical-conical tapered lighting column, seamless drawn, provided with two brackets for public lighting. The upper bracket is mountable. The requirement of the client for invisible bolds between the column and the bracket was ful filled. Preserving: hot dip galvanised + powder coating (RAL 9005)



conical tapered lighting columns
conical tapered lighting columns (seamless drawn)A post column with a length above ground level of 4 meter. Preserving: hot dip galvanised according to EN ISO 1461 and powder coated in RAL 9005.

Saturday, September 13, 2008

What is the lighting column?

What is the lighting column?


It means the column standing in a line, and in addition, it is the product which maximizes the mystique for the seers through colorful and splendid light production by adding splendid lighting effects to each column, and the installation of it at the tourist spots throughout the nation is tended to be increased.


Lighting Column
Lighting column
Lighting Column +Head
Lighting column










































































Tuesday, September 2, 2008

Street Lighting Innovations

Source: PUBLIC WORKS MAGAZINE
Publication date: June 13, 2008

By Sarah Goodale

Sarah Goodale is marketing manager for Sun Valley Lighting, Palmdale, Calif.

Street Lighting Innovations

It would be difficult to imagine any community without street lights. However, selecting fixtures that promote pedestrian and vehicle safety without over-lighting the surrounding landscape can be a challenge.

Most U.S. communities are committed to reducing light pollution or artificial 'sky glow,' the light that surrounds an urban area. Sky glow can result when light sources distribute light directly above a fixture's horizontal plane or indirectly from light that reflects upward from nearby surfaces. Advanced refractors and reflectors help meet today's 'dark sky compliant' mandates by directing light exactly where it is needed.

Reducing Light Pollution

Fixtures are now classified in four categories:

  • Full cut-off. Light is not distributed at or above the fixture's horizontal plane.
  • Cut-off. Aminimum amount of light is directed at a horizontal plane and light above the horizontal plane is within 2.5% of the total lamp lumens.
  • Semi cut-off. Light above the horizontal plane is less than 5% of the total lamp lumens.
  • Non cut-off. Aconsiderable amount of light is visible above the horizontal plane.

Today's fixtures feature precisionsegmented optics in a variety of light distribution patterns and lamp sizes and styles. Some fixtures, for example, have flat glass lenses to meet strict environmental standards; others are available with either vertical lamps for wide area lighting or horizontal lamps for roadway coverage.

Types of Lighting

Four types of lighting are used for most area and street lighting: fluorescent, metal halide, and high- and low-pressure sodium. LEDs are also becoming popular, but many communities are waiting for more extensive field testing before switching to them.

Fluorescent lights are often seen in commercial buildings. They are energyefficient, but operation in very cold temperatures can be an issue.

Metal halide offers a cool white light, is efficient, and uses long-lasting bulbs. It has good color rendition and is popular in street lighting.

Low-pressure sodium produces a yellow-orange light and is more efficient than high-pressure sodium. While the lamp's deep color makes it unacceptable for street lighting, it is useful for tunnels or near observatories.

High-pressure sodium is also efficient with longer-lasting lamps. It produces a warm golden-white color ideal for street lighting while delivering more light per Watt of electricity.

Finding a Fit

Many state transportation departments set standards for street lighting based on safe light levels for traffic. The most common choice for busy roadways has generally been a tall pole and a 'cobra head' fixture with a high-pressure sodium lamp.

However, in business districts that promote pedestrian traffic to restaurants and shops at night, walkway and streetscape lighting must be warm and inviting while addressing safety concerns. Lower intensity lights on shorter, closely spaced poles can light public areas without harsh shadows, which can be perceived as threatening.


Traditionally styled fixtures can enhance a revitalized downtown district by combining a vintage appearance with contemporary technology. These fixtures are available with full- and semi-cutoff light and a choice of light sources.

The most popular streetscape fixtures are made from heavy-wall cast aluminum construction and have a 3-mil polyester powder coating. In areas where vandalism is a concern, municipalities often select vandal-resistant fixtures constructed with metal cages around the lamps and finished with anti-graffiti coating on the pole and lamp head.

Selection Resources

During the initial stages of a new lighting project, a limited number of luminaires and related components should be identified for final selection. Manufacturers can provide resources such as design CDs, photometric information on mounting height recommendations and fixture spacing, layouts to assist with setting light levels and distribution, and submittal drawings of the selected assembly,including technical detail.

If there is a requirement to match existing luminaires, poles, or bases, the design team and in-house tooling department can be consulted about feasibility of reproduction. These services are typically available at no cost. Tooling costs for custom products can often be eliminated due to the large inventory of custom tooling available at major manufacturers.

When your community is ready to renovate existing lighting or is planning a new civic project, you can find environmentally sound fixture choices that offer the latest styling, technical advances, and low-cost maintenance features.

street lighting knowledge Base series I

lamp compartment which is covered by a transparent cover glass towards the front portion. (reference http://www.urbislighting.com/knowledgebase.php?cat=2&archive=1&sid=2005_3_7)
Making sure that luminaires remain as maintenance free as possible is very important to lighting engineers, and there are many different ways to seal the optical and control gear compartments to achieve this. We asked Bryan Shortreed, Engineering Support Manager at Urbis Lighting, about the different options available.

Why is keeping the optical compartment sealed so important?

"For a luminaire optical compartment, the choice is simple. If there is any ingress of dirt or moisture then the performance of the luminaire is affected, as the maintenance factor is reduced.

Additionally, there will also be a requirement for cleaning the inside of the optic, which will increase the time taken for maintenance. Therefore, it makes sense to choose a luminaire with an optical compartment tightness of IP66."


control gear compartment
Control gear consists of either a ballast, ignitor and capacitor(chinese reference ) for conventional control gear or an electronic ballast. There are often other electrical components such as a photocell or monitoring device.

The life of an electrical component is strongly related to the temperature at which it runs. If we take the conventional ballast as an example, the ballast manufacturer will specify a maximum temperature (TW) at which the ballast should be operated to give it a life of 10 years. Typically, if the ballast were to run through its life at 10 degrees above this figure then the ballast life would probably be halved. Similarly, if the ballast were to run cooler than the TW value through its life, then it would be reasonable to expect the ballast life to be significantly improved. All of the other electrical components behave in a similar manner."

Friday, August 29, 2008

Friday, August 22, 2008

Followers

Wordtime